← All news

Structural5 min read

Second-generation Eurocodes: where the UK transition stands

Both generations coexist until 30 March 2028. UK National Annexes are being published as they are ready, and Approved Document A is under review but not yet revised.

The second generation of Eurocodes is arriving in the UK in stages. BSI has set 30 March 2028 as the date when UK adoptions of the first-generation Eurocodes are withdrawn. Until then, both generations are available. The national documents that make the new codes usable in the UK are still being published, and the government guidance that points designers to them has not yet been revised.

This post sets out what has been confirmed, what has not, and what it means for preliminary figures like the ones on this site. It is a status note, not a guide to the technical changes.

What is confirmed

  • A coexistence period from 2023 to 2028. BSI says both generations are available during this time, so organisations can learn the changes, update their processes and plan projects.
  • Withdrawal on 30 March 2028. On that date the UK adoptions of the first generation are withdrawn. BSI says the same transition applies to UK National Annexes and the documents that support them. After that, the second generation becomes the recommended basis for Eurocode design.
  • A new Eurocode for structural glass. BSI notes that EN 19100 has been added as part of the update.
  • National Annexes as they become ready. BSI publishes second-generation UK National Annexes as soon as each is available. For example, the UK National Annex to BS EN 1990-1:2023+A1:2026, which covers the basis of structural and geotechnical design for new structures, was published on 30 September 2026.

The Eurocodes are not law. In England, they are one recognised way to show that a building meets the structural requirements of the Building Regulations, because Approved Document A refers to them. That link between the standards and the regulations is the part still to change.

Approved Document A: a review, not yet a new edition

The current Approved Document A on gov.uk is still the 2013 edition. Its Section 1 was last revised in May 2013, when references to withdrawn British Standards were replaced with references to the first-generation Eurocodes.

From 10 February to 21 April 2025, the Building Safety Regulator ran a call for evidence on reviewing Approved Document A, through HSE’s consultation site. It proposed revising the document to line up with the withdrawal of the first generation, so that its Eurocode references point to the second generation. It also described a wider review of the document. Among the topics it raised were works to existing buildings, the new EN 1990-2 on assessing existing structures, and how far design checking should be covered. It said the UK had not yet decided the nationally determined parts of the design-checking provisions in BS EN 1990:2023.

A call for evidence collects views before any draft. We have not seen a published draft or a revised edition, so we do not say what the new Approved Document A will contain or when it will arrive.

Update pending

The revised Approved Document A has not been published, and more second-generation UK National Annexes are still to come. We will update this post when the revised document is published on gov.uk. We will also check the position again by 29 January 2027, even if nothing has changed by then.

A worked example: what does not change

Much of a preliminary check is plain statics, and statics does not depend on which generation of code you use. What changes is what you do with the result: how actions are combined and which factors apply. Our beam reactions calculator shows the split.

EXAMPLE

A simply supported beam spans 6 m. Its characteristic loads are a permanent UDL of 5 kN/m and a variable UDL of 3 kN/m. Run each load through the calculator on its own.

  • Permanent: RA = RB = 15 kN, and Mmax = wL²/8 = 22.5 kN·m.
  • Variable: RA = RB = 9 kN, and Mmax = 13.5 kN·m.

These are characteristic values. They are the same under either generation. Check them in the beam reactions calculator.

To get a design value, you combine the two using the partial factors and combination rules in EN 1990 and its UK National Annex. That is the step that depends on the generation, and on which National Annex applies to the project. We do not quote factor values here. On a real project, the values come from the documents named in the project’s design basis, not from a news post.

What to check on a live project

  • The generation in the design basis. BSI stresses that designers, clients and manufacturers need to know which generation is in use and how the National Annexes apply. Do not mix parts from different generations, or pair an EN part with a National Annex written for the other generation.
  • Projects that span 2028. Designs started under the first generation may still be in progress after the withdrawal date. Agree early with the client and the checker which documents apply.
  • The status of each National Annex. Check BSI’s listing for each part you rely on. Some second-generation annexes are published and others are not.
  • Software and templates. Calculation tools often fix the code edition in the background. Record which edition a tool uses.

What it means for this site

Our structural calculators work out characteristic quantities: reactions, moments, stresses, deflections and buckling loads from first principles. They do not apply partial factors from either generation, so their results do not change at the transition. Where our guides name a Eurocode part, we plan to add the second-generation reference as the UK documents are published, and to retire first-generation references after 30 March 2028.

Illustrative only. Not design advice.

Sources

More from News

Electrical5 min read

BS 7671:2018+A4:2026 is now the current edition

The six-month overlap has ended. What the IET and BSI say changed in Amendment 4 (batteries, PoE, ICT functional earthing and medical locations), and why voltage drop matters more at extra-low voltage.

Read post →

← All news