Home · Calculators

Torque, shaft power and gear ratio calculator

Three rotating-machinery sums in one place.

Torque from a force

Worked examples

Example 1: Spanner

500 N at 0.25 m is 125 N·m.

Example 2: Handwheel

80 N at 0.4 m radius is 32 N·m.

Reading the result

If the force is not perpendicular, use only its perpendicular component.

Torque for bolts should come from the bolt manufacturer or specification.

Torque is the turning effect that a shaft, bolt or valve feels. The same torque can come from a small force on a long arm or a large force on a short one, which is why a longer bar makes a seized nut easier to move.

Typical values

SituationTypical figure
Hand on a 250 mm spanner, firm pullabout 250–400 N, so 60–100 N·m
Cycle crank, 170 mm, rider standingabout 700 N, so about 120 N·m
Valve handwheel, 200 mm radius80–150 N gives 16–30 N·m

Common mistakes

  • Measuring the radius to the end of the handle rather than to where the force is applied.
  • Using a force at an angle without taking its perpendicular component (F sin θ).
  • Mixing millimetres and metres: 250 mm is 0.25 m.

How to use

Enter the force in newtons and the radius in metres from the centre of rotation to the line of the force. The result is T = F × r, which assumes the force is perpendicular to the arm.

Edge cases

  • A zero radius gives zero torque. Negative radius is rejected; a negative force is allowed and shows the opposite direction.
  • If the force is not perpendicular, multiply by the sine of the angle between the force and the arm before entering it.
  • The tool does not check the strength of the spanner, bolt or shaft.

Questions

What if the 500 N force is at 60° to a 0.25 m arm?

The perpendicular part is 500 × sin 60° ≈ 433 N, so the torque is about 108 N·m, not 125.

How does this relate to power?

Torque times angular speed is power. Use shaft power with the speed.

How do I check a bolt tightening torque?

Divide the specified torque by the length of the spanner to find the force needed. For 125 N·m on a 0.25 m spanner, the force is 500 N, about the weight of a 51 kg mass. Use a calibrated torque wrench for any joint where the preload matters.

Shaft power

Worked examples

Example 1: Small drive

50 N·m at 1,450 rpm is 7.59 kW.

Example 2: Two-pole motor

200 N·m at 2,950 rpm is 61.8 kW.

Reading the result

This is the mechanical power at the shaft. Electrical input is higher by the motor efficiency.

Torque varies with load. Use the running torque at the duty point, not the starting torque.

Induction motors run a few per cent below synchronous speed. Using 1,500 rpm instead of a measured 1,450 rpm overstates power by about 3%.

Typical values

Motor speed (50 Hz)Synchronous / typical full-load speed
2-pole3,000 / about 2,900–2,950 rpm
4-pole1,500 / about 1,440–1,470 rpm
6-pole1,000 / about 960–980 rpm

Common mistakes

  • Using synchronous speed instead of the running (slip) speed.
  • Entering torque in kN·m in the N·m box.
  • Treating shaft power as electrical input power.

How to use

Enter the torque in newton-metres and the rotational speed in revolutions per minute. The result is the mechanical power at that shaft, P = 2πnT/60. Use the measured or nameplate full-load speed, not the synchronous speed.

Edge cases

  • Zero speed or zero torque gives zero power, which is correct: a stalled shaft holding torque does no work.
  • A negative torque or speed is accepted and gives negative power, meaning the shaft is being driven (braking or generating). Read the sign, not just the size.
  • The tool does not check whether the shaft, key or coupling can carry the torque.

Questions

What torque does a 7.5 kW motor give at 1,450 rpm?

Rearranging, T = 60P/(2πn) = 60 × 7,500 / (2π × 1,450) ≈ 49.4 N·m.

Why does power go up with speed for the same torque?

Power is torque times angular speed. 200 N·m at 2,900 rpm is about 60.7 kW, twice the power at 1,450 rpm.

How does this relate to motor ratings?

Motor nameplates give output power at the shaft. If you measure torque and speed on a running machine, this page gives the actual shaft power, which you can compare with the rating. Electrical input is higher by the motor efficiency, typically 85–95% for industrial motors.

Gear ratio and output speed

Worked examples

Example 1: Reduction

A 1,450 rpm motor driving a 20-tooth pinion into a 60-tooth gear: ratio 3, output 483 rpm.

Example 2: Lower-speed motor

A 960 rpm (six-pole) motor with a 15-tooth pinion and a 45-tooth gear: ratio 3, output 320 rpm. If the motor delivers 50 N·m, the ideal output torque is 150 N·m; at a 97% mesh efficiency it is about 146 N·m.

Reading the result

For a compound train, multiply the ratios of each pair. For belt drives use pulley diameters instead of teeth, and expect a little slip.

Efficiency is not applied. Spur gear meshes typically lose a few per cent each; worm gears can lose far more.

Speed × torque is roughly constant through a gearbox, less losses. That is why a reduction gearbox lets a small fast motor drive a slow heavy load.

Typical values

Driver : drivenRatio / output from 1,450 rpm
20 : 402 / 725 rpm
20 : 603 / 483 rpm
15 : 604 / 363 rpm
20 : 201 / 1,450 rpm

Common mistakes

  • Dividing driver by driven teeth, which inverts the ratio.
  • Forgetting that torque rises as speed falls.
  • Ignoring efficiency in a multi-stage train.

How to use

Enter the input speed in rpm and the number of teeth on the driving and driven gears. The result is the ratio and the output speed.

Edge cases

  • Tooth counts must be greater than zero; speed cannot be negative.
  • The ratio ignores slip, which does not occur with gears but does with belts.
  • Torque goes up by the same ratio that speed goes down, less losses.

Questions

What does a 960 rpm motor give through 15 to 45 teeth?

Ratio 3, output 320 rpm, with about three times the torque before losses.

What about compound gear trains?

Multiply the ratios of each stage.

What about an idler gear?

An idler between two gears changes the direction of rotation but not the ratio. The ratio still depends only on the first driver and the last driven gear in a simple train. In a compound train, where two gears share a shaft, each stage’s ratio is multiplied.

Basis

These are the standard definitions of torque, rotational power and gear ratio. No external data or design standard is involved.

Last checked 9 November 2026. See the methodology and the disclaimer.