Engineering unit converter
Eight quantities: temperature, length, area, volume, weight (mass), velocity, pressure and volumetric flow. Metric and imperial, with UK and US gallons kept separate.
What this tool covers
Choose a quantity, enter a value, pick From and To, and read the live result. Swap flips the units. Reset restores the defaults for the selected quantity.
- Temperature: °C, °F, K (absolute readings, not temperature intervals).
- Length: mm, cm, m, km, in, ft, yd, mi (international inch/foot/yard/mile).
- Area: mm², cm², m², km², ha, in², ft², yd², acre.
- Volume: mL, L, cm³, m³, in³, ft³, gal (UK), gal (US).
- Weight (mass): mg, g, kg, tonne, oz, lb, ton (UK long), ton (US short).
- Velocity: m/s, km/h, mph, ft/s, kn.
- Pressure: Pa, kPa, MPa, bar, mbar, psi, atm.
- Volumetric flow: m³/s, m³/h, L/s, L/min, L/h, ft³/s, ft³/min, gal/min (UK), gal/min (US).
Mass versus force, and volumetric versus mass flow
The Weight (mass) group converts mass only (kilogram and its relatives). It does not convert force units such as newton or pound-force. On drawings, “weight” is often used loosely for mass; this tool keeps the kilogram as the base.
The flow group is volumetric flow only. It does not convert mass flow (kg/s) or standard volumetric flow that depends on a stated density or gas condition. To get mass flow you still need density: ṁ = ρ × Q.
Worked examples
Example 1: Temperature
EXAMPLE. 20 °C → 68 °F → 293.15 K.
Example 2: Pressure
EXAMPLE. 150 psi → 10.34 bar (to two decimals).
Example 3: UK and US gallons
EXAMPLE. 1 gal (UK) → 1.201 gal (US). The imperial gallon is larger than the US liquid gallon.
Example 4: Flow
EXAMPLE. 10 L/s → 132.0 gal/min (UK) approximately.
Reading the result
Inch, foot, yard and mile here are the international definitions (1 in = 25.4 mm exactly).The acre is the international acre, 4,046.8564224 m².
UK (imperial) gallon = 4.546 09 L exactly. US liquid gallon ≈ 3.785 412 L. Labels always say which gallon is in use.
UK long ton = 2,240 lb. US short ton = 2,000 lb. The tonne (metric ton) is 1,000 kg exactly.
Gauge and absolute pressure are not distinguished; convert the number you have, then apply the atmospheric offset yourself if needed (1 atm = 101.325 kPa exactly).
Typical values
| Conversion | Result |
|---|---|
| 1 bar | 14.504 psi |
| 1 m | 3.2808 ft |
| 1 kg | 2.2046 lb |
| 1 m/s | 3.600 km/h |
| 0 °C | 32 °F / 273.15 K |
| 1 gal (UK) | 4.54609 L |
| 1 gal (US) | 3.785412 L |
Common mistakes
- Mixing UK and US gallons or tons.
- Treating a temperature interval (°C rise) the same as an absolute reading when converting to °F.
- Using this mass converter for force (lbf, N) or this flow converter for mass flow.
- Forgetting that acre on this page follows the NIST survey-foot-based factor.
Edge cases
- Blank or non-numeric input is rejected; the result area explains what to fix.
- Temperatures below absolute zero are rejected with an explicit message.
- Absolute zero itself (0 K / −273.15 °C / −459.67 °F) is accepted.
- Very large magnitudes (above 10¹²) are rejected so a units slip does not look like a real answer.
- Zero converts to zero for every non-temperature unit. For temperature, 0 means the zero of that scale, not “no temperature”.
Sources
- NIST SP 811, Appendix B.8 — conversion factors (inch, foot, gallon UK/US, pound, ton long/short, psi, knot, cubic foot, acre, and related entries).
- NIST Special Publication 811 — Guide for the Use of the SI.
- SI temperature relations as stated in NIST SP 811 (kelvin, degree Celsius, degree Fahrenheit).
Questions
Why are UK and US gallons different?
They are defined differently. NIST lists the Canadian and UK (imperial) gallon as 4.546 09 × 10⁻³ m³ and the US gallon as 3.785 412 × 10⁻³ m³. Always check which gallon a drawing or datasheet means.
Is weight the same as mass here?
No. This group converts mass. Weight as a force belongs with newtons or pound-force, which this page does not convert.
Can I convert a 10 °C temperature rise to °F?
Not with the absolute-reading formulas on this page. A 10 °C interval is an 18 °F interval (multiply by 1.8). Absolute conversion is for scale readings such as “the water is at 10 °C”.
Is 1 kN/m² the same as 1 kPa?
Yes. A pascal is one newton per square metre, so 25 kN/m² is 25 kPa.
Basis
Each result comes from a fixed conversion factor between units. It relies on no design standard. Check the units of any value you enter.
Last checked 5 November 2026. Worked figures are labelled EXAMPLE. Factors are from published sources linked above. See methodology and the disclaimer.